BrewBuilt X3 Uni 26 L

New features:

• A professional 8" Tri-Clamp lid replaces the classic “Band Clamp” found on traditional conical fermenters. (Allows easy closing and 100% safe pressurization.)

• Four reinforced legs with crossbars, flared, creating the most stable base and offering better access to the front fittings and the drain system. (You can also install casters on them.)

• 3 horizontal conical ports on the cone section, allowing your racking arm, carbonation stone or thermowell to sit horizontally inside your BrewBuilt X3.

• Oversized 3" bottom port and butterfly valve with Flex Chamber TC 3" collection jar.

The new BrewBuilt X3 Uni sets the new standard of quality.

Fully built from 304 stainless steel, with flawless welds and a dazzling mirror-polished finish inside and out. The BrewBuilt X3 Uni is easy to sanitize and even nicer to look at.

Functional and Instagrammable! #BrewBuilt.

Double-wall “External Cooling Jacket”:

When it comes to temperature control, the gold standard has always been the double wall (“External Cooling Jacket”).

Internal cooling coils have long been the solution and, although simpler to manufacture and relatively inexpensive, they are harder to clean and struggle with rapid cooling in warm environments. The BrewBuilt X3 Uni offers maximum cooling power without compromising hygiene.

The two 1.5" TC ports located at the back of the fermenter allow connection to glycol chillers such as the Icemaster G20.

Oversized 3" TC dump valve

The largest of its kind for this type of fermenter. Try the biggest Dry Hop you can — you still won’t clog this opening.

With this oversized 3" bottom port, you’ll have all the space needed to easily evacuate your dry hop additions. The mirror-polished interior finish allows flocculating yeast to collect cleanly at the bottom of the cone, sliding along perfectly smooth walls.

The butterfly dump valve integrates perfectly with the Flex Chamber collection jar.

Four-leg stability reinforcement:

There is a common complaint about instability with three‑leg units. While they may suffice when the fermenter is stationary on a flat surface, users often end up buying a reinforcement shelf — especially if they add casters or leg extensions.

This is why BrewBuilt designed the X3 inspired by the best brewery fermenters, resting on a reinforced four‑leg base. This design feature makes the X3 fermenter extremely stable compared to other models.

This reinforced four‑leg system is rock solid. This is crucial if you plan to add casters to easily move the fermenter around your brewery.

Not only does this design improve stability, it also increases height, eliminating the need for extensions in almost all situations. An elbow, sight glass or Flex Chamber can be mounted under the unit with the required clearance.

Adjustable legs:

The BrewBuilt X3 Uni comes with reinforced adjustable screw legs. If your brewery floor is uneven (sloped, for example), you can quickly and easily level the fermenter. The legs can be replaced at any time with high‑quality casters.

Flex Chamber Collection Jar – Trub separator and yeast harvester

In collaboration with KegLand, BrewBuilt developed the pressurizable Flex Chamber Collection Jar. It attaches directly to the butterfly valve and can be used to remove hop residues or harvest yeast, for example.

Made from crystal‑clear Triton, you can visually monitor fermentation activity just like with a sight glass. Ball Lock adapters can be attached to the threaded ports on each side, allowing you to connect oxygenation or carbonation stones, or purge the Flex Chamber with CO₂ and use it to inject hops or other ingredients.

“Pressure Pack” lid with Clear Float technology

With its pressurization capacity up to 14 psi, the BrewBuilt X3 Uni allows you to ferment, carbonate and even serve your beer directly.

The Pressure Pack lid features the unique Clear Float Technology racking tube, which can be used to take samples, transfer to a keg or serve finished beer. This innovative feature draws beer from the top, meaning you always get the clearest, least sedimented beer possible.

Using pressure to take a sample from the floating dip tube also eliminates the small amount of oxygen that would otherwise enter your beer under classic fermentation conditions.

Pressure transfer from fermenter to keg is the best way to protect your beer from oxygen when it is at its most vulnerable. Kegging can be considered the final hurdle of the brewing process, where limiting oxygen exposure is crucial. It can make the difference between a beer that stays excellent for months and a beer that oxidizes within a week. Don’t take risks. Use the Pressure Pack to keg from the top down and leave sediment behind.

Full list of BrewBuilt X3 Uni features:

• Double-wall glycol cooling jacket with 1.5" Tri-Clamp fittings
• Pressure Pack lid with Clear Float (floating dip tube)
• Flex Chamber Collection Jar, a transparent pressurizable jar allowing fermentation viewing, hop residue removal and accessory connection
• Wide base with 4 legs for stability
• 304 stainless steel construction
• Mirror-polished finish
• Industry-leading interior welds – uniquely ground and polished
• (1) 2" TC port for immersion heating
• (3) welded horizontal conical ports
• (1) 8" lid opening with 8" TC clamp
• (5) 1.5" TC openings on the lid
• 3" bottom dump port with 3" TC butterfly valve
• 1.5" thermowell for temperature probe insertion
• (4) adjustable legs
• Silicone blow-off hose
• Three‑piece 8" stainless Tri-Clamp and one‑piece molded gasket
• Integrated 15 psi PRV

Volumes and Dimensions:

• Gross volume (lid + collection jar): 29.37 L
• Net volume: 26 L
• Minimum recommended volume: 1.5 L
• Maximum recommended volume: 25 L
• Total height: 96.52 cm
• Total width: 54.102 cm