Brewtools – FCS One Starter Kit Unitank – Density, Temperature & Pressure Measurement

Included parts:

• - FCS One DC24V with power supply
• - Pressure sensor CAN BUS 24 V, M12
• - Solenoid valve TC34 mm + M12, DC24V Ø2.0
• - Density/temperature sensor 300 mm, TC 1.5", CAN BUS 24 V
• - LP12 5-pin cable, 3 m (2 pcs)
• - LP12 2-pin cable, 3 m
• - LP12 2-pin to DIN 43650 Type B adapter
• - TC34 mm airlock (2-part)
• - Ball mount system (quick clamp + 60 mm rod)
• - Tri‑Clamp + gaskets for the airlock

Recommended parts (not included):

• - Cooling solenoid valve with adapters/cables, or submersible pump
• - Adapters and fittings to match your tank if it is not a Brewtools tank, or if it is already heavily equipped
• - FCS I/O Module for full automation

About this kit version:

The Brewtools FCS One Temperature & Density Starter Kit is the “light” version, designed for a faster and more compact installation than the FCS Unitank Starter Kit.

Like it, it allows electronic control of the spunding valve as well as fermentation temperature.

Main difference: number of available ports

• - FCS One: 2 CAN ports + 2 DC 24 V ports
• - FCS Unitank Starter Kit and FCS Density & Temperature V2: 4 CAN ports + 4 DC 24 V ports
• - FCS I/O Module not included

For non‑Brewtools tanks, an adapter and/or a tee may be required to connect the purge valve + pressure sensor assembly.

How it works:

The sensors installed on your Unitank continuously measure:

• - temperature
• - pressure
• - density

The data is sent to the FCS Display Module, which shows the values in real time and records the history for analysis.

Scalable system:

The Brewtools FCS ecosystem is fully modular. You can later add:

• - additional sensors (level, agitation…)
• - solenoid valves (cooling, transfer…)
• - expansion modules

This allows you to gradually increase the level of automation of your setup.

Ideal for:

• - Advanced homebrewers
• - Microbreweries and pilot systems
• - Installations seeking professional fermentation control
• - Brewers wanting automation without designing a full system themselves

Included parts:

• - FCS One DC24V with power supply
• - CAN BUS 24V pressure sensor, M12
• - TC34 mm solenoid valve + M12, DC24V Ø2.0
• - 300 mm density/temperature sensor, TC 1.5", CAN BUS 24V
• - LP12 5‑pin cable, 3 m (2 pieces)
• - LP12 2‑pin cable, 3 m
• - LP12 2‑pin to DIN 43650 Type B adapter
• - Two‑part TC34 mm airlock
• - Ball‑joint mounting system (quick clamp + 60 mm rod)
• - Tri‑Clamp + gaskets for the airlock

Recommended parts (not included):

• - Cooling solenoid valve with adapters/cables, or submersible pump
• - Adapters and fittings to match your tank if it is not a Brewtools tank, or if you already have many accessories installed
• - FCS I/O module for measurement expansion

About this kit version:

The Brewtools FCS One Temp Measurement Starter Kit is the “light” version, designed for a faster and more compact installation than the FCS Unitank Starter Kit.

Unlike the higher version equipped with the FCS Display Module 5″ and the dedicated I/O module, this version is based on the FCS One, a more compact and simpler controller, ideal for minimalist setups or tanks with few accessories.

Like the higher version, it allows electronic control of the spunding valve as well as fermentation temperature.

Main differences compared to the higher version:

• - Simpler interface: FCS One (all‑in‑one) instead of the 5″ FCS Display Module (more measurements but requires the FCS I/O module)
• - More compact installation and less cabling (FCS One = 2 CAN ports + 2 DC 24V ports VS 4 CAN ports + 4 DC 24V ports for the 5″ FCS Display Module)
• - Ideal for tanks with limited automation needs

For non‑Brewtools tanks, an adapter and/or a tee may be required to connect the purge valve + pressure sensor assembly.

Operation:

The sensors installed on your Unitank continuously measure:

• - temperature
• - pressure
• - density

The data is sent to the FCS Display Module, which shows real‑time values and records history for analysis.

Scalable system:

The Brewtools FCS ecosystem is fully modular. You can later add:

• - additional sensors (level, agitation…)
• - solenoid valves (cooling, transfer…)
• - expansion modules

This allows you to gradually increase the level of automation of your setup.

Ideal for:

• - Advanced homebrewers
• - Microbreweries and pilot systems
• - Setups seeking professional fermentation control
• - Brewers wanting automation without designing a full system themselves